Pennsylvania CDL › Practice tests
PA CDL Air Brakes Practice Test
Covers how air brakes work, the air brake checks you do before driving, low-air warnings, spring brakes, brake lag and braking on downgrades.
- 25questions on the real test
- 20correct to pass (80%)
- 25practice questions here
The 25-question count is from PennDOT's CDL Fact Sheet (June 2025). The 80% passing score is the federal minimum for every CDL knowledge test (49 CFR 383.135).
Study from Section 5 of the PennDOT Commercial Driver’s Manual (PUB 223). Required for: Driving a CDL vehicle with air brakes. Without it, your CDL carries PennDOT's L/Z air brake restriction.
Pick an answer to see if you're right and why.
Like the real test: no hints. Answer everything, then submit for your score.
Correct answer: B. The service system works with the brake pedal, the parking system with the parking brake control, and the emergency system uses parts of both to stop the vehicle if the brake system fails.
Manual: Section 5, Air Brakes (introduction) (p. 5-1)
Correct answer: A. The governor cuts the compressor out at around 120 to 140 psi and lets it start pumping again (cut in) when pressure falls to around 100 psi.
Manual: Section 5, Air Brake System Parts: Air Compressor Governor (p. 5-1)
Correct answer: D. The compressor should cut back in at around 100 psi and cut out at around 120 to 140 psi. Check the manufacturer's numbers for your vehicle.
Manual: Section 5, Inspecting Air Brakes: Final Air Brake Check (p. 5-7)
Correct answer: C. Compressed air carries water and oil that settle at the bottom of each tank. Both are bad for the system, and frozen water can make the brakes fail.
Manual: Section 5, Air Brake System Parts: Air Tank Drains (p. 5-1)
Correct answer: A. Manual drains (a quarter-turn valve or a pull cable) need to be opened by you at the end of every driving day. Automatic drains do it for you.
Manual: Section 5, Air Brake System Parts: Air Tank Drains (p. 5-1)
Correct answer: B. The safety valve keeps the system from over-pressurizing and is usually set at 150 psi. If it releases air, something is wrong and a mechanic should fix it.
Manual: Section 5, Air Brake System Parts: Safety Valve (p. 5-2)
Correct answer: D. Each release lets air out of the system. Fanning the pedal can drain the tanks faster than the compressor refills them, and if pressure gets too low the brakes won't work.
Manual: Section 5, Air Brake System Parts: The Brake Pedal (p. 5-2)
Correct answer: C. S-cam drum brakes are the most common. Wedge and disc brakes are used less often.
Manual: Section 5, Air Brake System Parts: Foundation Brakes (p. 5-2)
Correct answer: A. Needing more application pressure for the same result means the brakes are fading. Leaks, poorly adjusted brakes or other mechanical trouble can cause the same thing.
Manual: Section 5, Air Brake System Parts: Application Pressure Gauge (p. 5-3)
Correct answer: A. A visible warning, usually a red light and sometimes a buzzer, must turn on before pressure falls under 55 psi. Large buses often warn earlier, at 80 to 85 psi.
Manual: Section 5, Air Brake System Parts: Low Air Pressure Warning (p. 5-3)
Correct answer: B. The "slippery" setting cuts front brake pressure in half and reduces your stopping power. Tests show front wheels are unlikely to skid from braking even on ice, so keep it on normal.
Manual: Section 5, Air Brake System Parts: Front Brake Limiting Valve (p. 5-3)
Correct answer: A. Spring brakes come fully on somewhere between 20 and 45 psi, typically 20 to 30. Don't wait for that to happen.
Manual: Section 5, Air Brake System Parts: Spring Brakes (p. 5-3)
Correct answer: B. Stop while there's still enough air to use the foot brake. If you wait for the spring brakes, a loaded truck may take a long way to stop and a light one may skid.
Manual: Section 5, Using Air Brakes: Low Air Pressure (p. 5-10)
Correct answer: B. The yellow diamond-shaped knob controls the parking (spring) brakes: pull it out to set them and push it in to release. Older vehicles may use a lever instead.
Manual: Section 5, Air Brake System Parts: Parking Brake Controls (p. 5-4)
Correct answer: D. With both the spring force and the air pressure pushing, the brakes can be damaged. Some systems prevent this, but not all, so make it a habit not to do it.
Manual: Section 5, Air Brake System Parts: Parking Brake Controls (p. 5-4)
Correct answer: C. Let the compressor build at least 100 psi in both halves of the system. The low air warning should shut off once both are above the level the manufacturer set, which must be more than 55 psi.
Manual: Section 5, Dual Air Brake Systems (p. 5-6)
Correct answer: B. With the truck on level ground, wheels chocked and parking brakes off, pull firmly on each slack adjuster you can reach. About an inch of movement at the push rod means it likely needs adjusting.
Manual: Section 5, Inspecting Air Brakes: Walkaround Inspection (p. 5-6)
Correct answer: D. Out-of-adjustment brakes are the problem inspectors find most often. Too much brake slack can make a vehicle very hard to stop.
Manual: Section 5, Inspecting Air Brakes: Walkaround Inspection (p. 5-6)
Correct answer: C. If an automatic adjuster is out of limits, something mechanical is wrong. Adjusting it manually is only a temporary fix in an emergency and can give a false sense of safety.
Manual: Section 5, Inspecting Air Brakes: Walkaround Inspection (p. 5-6)
Correct answer: A. A crack in a drum or disc can't run longer than half the width of the friction surface. Also check that linings aren't loose, oil-soaked or too thin.
Manual: Section 5, Inspecting Air Brakes: Walkaround Inspection (p. 5-7)
Correct answer: C. With brakes released, a single vehicle should lose less than 2 psi a minute and a combination vehicle less than 3. More than that means a leak that must be fixed before you drive.
Manual: Section 5, Inspecting Air Brakes: Final Air Brake Check (p. 5-7)
Correct answer: D. With the foot brake held for a minute, losing more than 3 psi (single vehicle) or 4 psi (combination) is too much. Find and fix the leak before driving.
Manual: Section 5, Inspecting Air Brakes: Final Air Brake Check (p. 5-7)
Correct answer: D. Pressure should climb from 85 to 100 psi within about 45 seconds (longer can be fine with bigger-than-minimum tanks; check the specs). Slow buildup can leave you short of air while driving.
Manual: Section 5, Inspecting Air Brakes: Final Air Brake Check (p. 5-7)
Correct answer: C. Hydraulic brakes act almost instantly, but air needs time to reach the brakes. At 55 mph on dry pavement, that lag adds roughly 32 feet to your stopping distance.
Manual: Section 5, Using Air Brakes: Stopping Distance (p. 5-9)
Correct answer: C. Very hot brakes can be damaged, and wet brakes can freeze in place. Chock the wheels on level ground instead, and let hot brakes cool before setting the parking brakes.
Manual: Section 5, Using Air Brakes: Parking Brakes (p. 5-10)