Ohio CDL Air Brakes Practice Test
Covers the parts of an air brake system, dual air systems, the air brake checks you do before driving, spring brakes, low-air warnings, brake lag and emergency stops.
- 80%correct to pass
- 27practice questions here
The 80% passing score is the federal minimum for every CDL knowledge test (49 CFR 383.135). The Ohio BMV doesn't publish how many questions are on its test, so ask at the driver exam station.
Study from Section 5 of the Ohio BMV Commercial Driver License Manual (HSY 7605). Required for: Driving a CDL vehicle with air brakes, including air-over-hydraulic. Without it, your CDL carries an L (no air brakes) restriction.
Pick an answer to see if you're right and why.
Like the real test: no hints. Answer everything, then submit for your score.
Correct answer: B. The service brakes stop you in normal driving, the parking brakes hold the parked vehicle, and the emergency system borrows parts of the other two to stop you if the brake system fails.
Manual: Section 5, Air Brakes (introduction) (p. 5-1)
Correct answer: A. A compressor can be lubricated by engine oil or have its own supply. If it has its own, checking that oil level is part of getting ready to drive.
Manual: Section 5, Air Compressor (5.1.1) (p. 5-1)
Correct answer: D. Cut-out is around 125 psi. When pressure falls back to the cut-in level, around 100 psi, the governor lets the compressor pump again. Check the manufacturer's numbers for your vehicle.
Manual: Section 5, Air Compressor Governor (5.1.2) (p. 5-1)
Correct answer: C. The compressor should cut back in at about 100 psi and cut out at about 125 psi. During your final air brake check you fan the brakes to bring pressure down and watch that the compressor starts again near the specified cut-in.
Manual: Section 5, Step 7 Final Air Brake Check (5.3.3) (p. 5-6)
Correct answer: A. Compressed air carries some water and oil, which settle in the bottom of the tanks. In cold weather that water can freeze and cause brake failure, so drain the tanks completely.
Manual: Section 5, Air Tank Drains (5.1.4) (p. 5-1)
Correct answer: B. With manual drains (a valve you turn a quarter turn or a cable you pull), it's on you to drain the tanks at the end of each driving day. Automatic drains do it for you.
Manual: Section 5, Air Tank Drains (5.1.4) (p. 5-1)
Correct answer: D. The evaporator puts alcohol into the air to lower the risk of ice in valves and other parts. Check and fill it daily in cold weather. You still need to drain the tanks daily unless they have automatic drains.
Manual: Section 5, Alcohol Evaporator (5.1.5) (p. 5-1)
Correct answer: C. The safety valve usually opens at 150 psi to protect the system from too much pressure. If it ever lets air out, something is wrong, so have a mechanic fix it.
Manual: Section 5, Safety Valve (5.1.6) (p. 5-2)
Correct answer: A. Each release lets some compressed air out, and the compressor has to make it up. Fan the pedal needlessly and pressure can drop low enough that the brakes won't work.
Manual: Section 5, The Brake Pedal (5.1.7) (p. 5-2)
Correct answer: A. S-cam drum brakes are the most common. Wedge brakes and air disc brakes are used too, but less often.
Manual: Section 5, Foundation Brakes (5.1.8) (p. 5-2)
Correct answer: B. Needing more application pressure for the same speed means the brakes are fading. Slow down and shift to a lower gear. Brakes out of adjustment, air leaks or mechanical problems can also cause it.
Manual: Section 5, Application Pressure Gauge (5.1.10) (p. 5-2)
Correct answer: A. The warning must come on before tank pressure falls below 55 psi. (Some older vehicles use half the governor cut-out pressure instead.) It's usually a red light, sometimes with a buzzer.
Manual: Section 5, Low Air Pressure Warning (5.1.11) (p. 5-2)
Correct answer: B. The "slippery" setting cuts front brake pressure in half, which reduces your stopping power. Tests show front-wheel braking skids are unlikely even on ice, so leave it on "normal."
Manual: Section 5, Front Brake Limiting Valve (5.1.13) (p. 5-3)
Correct answer: B. Spring brakes are held off by air pressure. When pressure falls to somewhere between 20 and 45 psi (typically 20 to 30), the springs put the brakes on. Don't wait for that: stop safely as soon as the low air warning comes on.
Manual: Section 5, Spring Brakes (5.1.14) (p. 5-3)
Correct answer: D. Pull the yellow diamond-shaped knob out to set the parking (spring) brakes, and push it in to release them. Older vehicles may use a lever or a different knob.
Manual: Section 5, Parking Brake Controls (5.1.15) (p. 5-3)
Correct answer: C. The springs and the service brake air push on the same parts, and together they can damage the brakes. Some systems prevent this, but not all, so make a habit of keeping off the pedal while the spring brakes are set.
Manual: Section 5, Parking Brake Controls (5.1.15) (p. 5-3)
Correct answer: B. Tractors, trucks and buses have a yellow ABS lamp on the instrument panel. Trailers have a yellow lamp on the left side, at either the front or rear corner.
Manual: Section 5, Antilock Braking Systems (5.1.16) (p. 5-4)
Correct answer: D. Give the compressor time to build at least 100 psi in both systems. The low air warning going out isn't enough: it can shut off at any manufacturer-set pressure above 55 psi.
Manual: Section 5, Dual Air Brake (5.2) (p. 5-5)
Correct answer: C. If a slack adjuster moves more than about an inch where the push rod connects, it probably needs adjustment. Brakes out of adjustment are the most common problem found at roadside inspections.
Manual: Section 5, During Step 5 Walk-around Inspection (5.3.2) (p. 5-6)
Correct answer: A. An automatic adjuster that's out of limits points to a mechanical problem in the adjuster or brake parts, or a bad installation. Adjusting it by hand masks that and the brake will soon be out again, so treat a manual adjustment as an emergency fix only.
Manual: Section 5, During Step 5 Walk-around Inspection (5.3.2) (p. 5-6)
Correct answer: C. Drums (or discs) must not have cracks longer than half the width of the friction area. Also check that linings aren't loose, oil-soaked or dangerously thin.
Manual: Section 5, During Step 5 Walk-around Inspection (5.3.2) (p. 5-6)
Correct answer: D. With the foot brake applied, a combination vehicle may lose up to 4 psi in one minute (3 psi for a single vehicle). Any more and you need to find and fix the leak before driving.
Manual: Section 5, Step 7 Final Air Brake Check (5.3.3) (p. 5-6)
Correct answer: D. Dual systems should go from 85 to 100 psi within 45 seconds. Larger-than-minimum tanks can take longer and still be safe, so check the manufacturer's spec. The 3-minute figure is for old single systems building from 50 to 90 psi at idle.
Manual: Section 5, Step 7 Final Air Brake Check (5.3.3) (p. 5-7)
Correct answer: C. Brake fully, release when the wheels lock, and brake fully again once they're rolling. It can take up to a second for the wheels to roll again, and reapplying too soon won't let the vehicle straighten out.
Manual: Section 5, Emergency Stops (5.4.3) (p. 5-8)
Correct answer: C. Air takes half a second or more to reach the brakes, which adds about 32 feet at 55 mph. That makes the total stopping distance for an air-braked vehicle over 450 feet at that speed.
Manual: Section 5, Stopping Distance (5.4.4) (p. 5-8)
Correct answer: C. You can only brake under control while there's air left in the tanks. If you wait for the spring brakes, a loaded truck takes a long way to stop because they don't work on all axles, and a light truck or a slippery road can send you into a skid.
Manual: Section 5, Low Air Pressure (5.4.7) (p. 5-9)
Correct answer: A. Very hot brakes, such as right after a long downgrade, can be damaged by the parking brakes. Very wet brakes in freezing weather can freeze in place. Chock the wheels on level ground and let hot brakes cool first.
Manual: Section 5, Parking Brakes (5.4.8) (p. 5-9)